HOOK UP TWO SUBS TO ONE AMP


Hook Up Two Subs To One Amp

DOMINATION
1010 views

FREE SEX VIDEO

| 1 :: 2 :: 3 :: 4 :: 5 |

hooking up 2 subs to a single amp? | Yahoo Answers

If the bass and sub-bass are quiet or not present at all, something is mis-wired. My own ikkle world. He is paying for everything.

  • Answer Questions Is there a way to fix the CD player in my car? Aug 6, Messages:
  • If I wanted to see pictures of shi t, i would have taken a couple of turds out of my toilet and used a whole role of film on them.
  • The term "bridging sub-woofers" is a bit misleading.

Next, connect the negative end of the first coil to the positive end of the second coil. Aftermarket stereo making static noise? Share this post Link to post Share on other sites.

DESCRIPTION: Amal99 , Jan 19, If you are working on a car stereo system you can simply disconnect the battery terminals. Speaker Selector Switch Simulators. Not Helpful 0 Helpful 0.


Helmut Kv?nig: I LOVE THE SECOND BBW!

Mara P.C.: Nice to be on the receiving end of that!

NoOneKnows: 82:00 she is the best!

John Drew: I love Madeleine. she is so cute

MuyBien: It necessary baby,it necassary.Very good vid.

PaulARTS: Are there any more videos of this pair? She is incredible and so.oooooo much fun!B

Get a roll of stereo wire. Member , Jan 19, Bridging is a term used for combining 2 channels of an amplifier to one. This will give a 1 ohm load. Hello Geoff, Thanks for your mostexcellent articles.

Best Way To Connect 2 Subwoofers To 1 Output?

Most HiFi amps are designed to have a total load impedance of 4 ohms or higher, but not lower than Subw ohms. Since an amplifier produces more wattage at a lower impedance, the parallel connection ensures you'll get the most output from your amp. How Multiple Speakers Share Power.

Jan 19, at When there is a long cable run to be split to go to both speakers Parallel: Learning the ins and outs of a bridged circuit is important, though, as an improper setup can damage your equipment. When there is a long cable run to be split to go to both speakers.

  • Hooking up 2 subs to a single amp?
  • Again, you have the series verses parallel debate. While this is safer for the amplifier it does mean the amplifier will also produce slightly less power.
  • Trending Now
  • Connecting them in series adds their impedance together, that is your two 3 ohm speakers wired in series would give you a 6 ohm load to the amplifier. The Fen Edge Ratings:

Posted on Tuesday, February 10, - Prev 1 2 Next Page 1 of 2. The resistor does take some power, but in a domestic install this is normally quite okay.

Thanks x 1 List. If I wanted to see pictures of shi t, i would have taken a couple of turds out of my toilet and used a whole role of film on them. To wire them in series you could follow the top right-hand diagram in the article above. Jan 19, at 7: Then wire positive to positive and negative to negative between the woofers, and likewise also to the amplifier. Lolz get good subs and amp imo.

Answer this question Flag as You should have at least four different values written down. The impedance of the speakers should be written on the back of the speaker or speaker box. You may want to connect 2 speakers to one amplifier without individual switching or volume controls if you:. For example if you have two subs that each pull W, you would want an amp that produces a minimum of W. I have been doing some reading about ohms law Last edited by a moderator:

7 Comments

Leave a Reply

Your e-mail will not be published. Required fields are marked *